Skip to content

Steps & Staircases

Resin Bound Steps & Staircases in Peterborough

Worn concrete or brick steps restored with a textured, anti-slip aggregate finish across treads, risers, and nosings.

  • Substrate Assessed First
  • Itemised Quote
  • Anti-Slip Finish
A beautifully landscaped large garden features a resin-bound patio leading to a brick house and an ornate greenhouse in the distance.

What Goes Wrong

Where resin bound steps fail, and how to avoid it

The finish is only as good as the preparation beneath it. These are the failure modes that matter.

Skipped Substrate Check

Applying resin over damp or cracked concrete without remedial work causes the layer to delaminate within months.

Survey Before Application

A specialist assesses cracks, damp ingress, and level at survey stage before any material is committed.

Smooth Finish on Steps

A resin finish without adequate aggregate texture becomes slippery when wet, a real hazard on exposed front entrances.

Textured Aggregate Mix

Aggregate is mixed into the UV-stable polyurethane resin binder, producing a textured surface with grip in wet conditions.

Unfinished Nosings

Edges and nosings left without a neat finish chip quickly under foot traffic, leaving the step front looking worse than before.

Nosings Finished Neatly

Each edge nosing is hand-finished individually to prevent chipping and give a clean, consistent line at the step front.

Mismatched Aggregate

Steps finished in a different aggregate to an adjoining resin surface look patchy and reduce the overall kerb appeal.

Aggregate Matched to Spec

Where steps adjoin an existing resin bound surface, aggregate selection is matched to maintain a consistent appearance.

Scope of Work

What resin bound step surfacing covers

The work spans every component of the step, not just the tread you walk on.

Concrete Substrate Surfacing

Resin bound finish applied over sound concrete steps.

Brick Substrate Surfacing

Suitable for older brick-built front entrance steps.

Matching Existing Resin Surfaces

Aggregate matched to an adjoining resin bound finish.

Anti-Slip Aggregate Finish

Textured surface for exposed or wet-weather entrances.

Steps That Hold Their Finish

Resin bound surfacing for steps, grip, substrate, and a finish that lasts

Worn concrete or brick steps are often structurally sound, the substrate assessment confirms whether resin bound surfacing is the right route.

Request a Survey

Many Peterborough properties have original brick or concrete front steps that are worn but intact. Rather than replacing the structure, a resin bound finish can be applied across the treads, risers, and nosings to restore appearance and improve grip. The aggregate mixed into the resin binder creates a textured surface that provides traction when wet, addressing the slipperiness concern that smooth concrete or painted steps often present.

Before any material is applied, the substrate is assessed for cracks, damp penetration, and level. A cracked or damp substrate will cause the resin bound layer to delaminate over time, so these issues are addressed during preparation. Stable hairline cracks are filled; structural cracks or damp ingress require remedial work first. The specialist confirms the substrate condition at the survey stage.

Application covers each tread and riser individually, with edge nosings finished neatly to prevent chipping at the step front. Where steps adjoin an existing resin bound surface, aggregate selection can be matched to maintain a consistent appearance. The cured finish requires no sealing and can be jet-washed to maintain its texture and colour.

Why Choose Us

Why Peterborough Resin Bound for steps & staircases?

Accountability at every stage, from the first assessment to the finished nosing.

Substrate Assessment Before Any Quote

A local specialist checks the base condition before a price is agreed, no surprises after work starts.

Itemised Quotation, Line by Line

Preparation, substrate remediation, and finish are quoted separately so you see exactly what each element costs.

Vetted Independent Local Partners

We connect you with vetted local specialists who work on Peterborough properties, not a national call centre.

No Work Agreed Without Survey

Nothing is committed until the substrate has been assessed and the quote accepted, the process protects you.

A completed resin driveways job at a house
A finished resin driveways project

The Process

From enquiry to finished steps

Request a Survey

  1. 01

    Describe Your Steps

    Tell us the number of steps, the existing substrate, and any visible cracks, damp, or unevenness you have noticed.

  2. 02

    Survey & Itemised Quote

    A local specialist visits, assesses the substrate condition, and provides a quote with preparation and finish as separate lines.

  3. 03

    Preparation & Application

    The substrate is prepared, any remedial work completed, and the resin bound aggregate finish applied across treads, risers, and nosings.

Pricing Estimates

Typical Resin Bound Steps & Staircases Prices

JobTypical cost
Small resin bound step area£600-£1,200
Medium resin bound stair run£1,200-£1,800
Complex steps and landings£1,800-£3,000
These prices are estimates and often vary with the condition, size and scope of each job. Message or call us for a free, no-obligation quote.
See all prices

Common Questions

Questions about resin bound steps

  • Are resin-bound steps slippery when wet?

    No. Resin-bound surfacing is porous and textured, so water drains through rather than pooling on the surface. The aggregate stones create natural grip underfoot, making it significantly less slippery than smooth concrete, painted surfaces or glazed tiles when wet.

  • Can resin-bound surfacing go over old concrete or brick steps?

    Yes, in most cases. A local specialist assesses the existing base first to confirm it is structurally sound, level and dry enough to bond to. Concrete and brick steps that pass that check can take a resin overlay without full removal.

  • Do my existing steps need a lot of preparation before resin can go on?

    It depends on the condition of the base. Loose material, cracks and contamination must be addressed before laying. A pre-quote site assessment identifies exactly what preparation is needed, so you know the scope before any work begins.

  • Will resin steps work properly if the steps are uneven or damp?

    Not without remedial work first. Resin applied over an uneven or damp base will not bond correctly and is likely to lift. The base assessment arranged before quoting identifies these issues, and any levelling or drying-out work is quoted separately before proceeding.

  • What is included in a resin-bound steps quote?

    Quotes are itemised as separate lines covering excavation or preparation, sub-base work, drainage where needed, and the resin-bound finish itself. That breakdown lets you see exactly what each element costs rather than a single combined figure.

  • Is resin-bound surfacing a better choice than tiles for my steps?

    For outdoor steps, resin-bound surfacing has practical advantages over tiles. It drains water through the surface rather than letting it sit, reducing slip risk. It also has no grout lines to crack or harbour moss, and it bonds as a continuous layer rather than individual pieces that can loosen.

  • Would resin steps be cheaper than paving or painting my steps?

    Paint is cheaper upfront but needs reapplying regularly and offers poor grip when wet. Resin-bound surfacing typically costs more initially than paint but less than full re-paving. Most resin-bound steps jobs come in at £600-£1,200, depending on the number of steps and base condition.

  • How do resin-bound steps compare with a DIY or handyman job?

    Resin-bound surfacing requires precise mixing ratios, correct base preparation and fast application before the resin sets. An incorrect mix or poorly prepared base leads to lifting, cracking or colour inconsistency. A vetted specialist with the right equipment produces a finish that bonds correctly and lasts.

More questions about Resin Bound Steps & Staircases?

Get Your Steps Assessed

Tell us about your existing steps and we will arrange a local specialist to check the substrate and quote every element separately.

Request a Survey